MTP 15HD A Series |
|
Video |
Gain |
Unity |
Number/signal type |
1 set of proprietary analog signals |
Connectors |
|
MTP R 15HD RSA D |
1 female RJ-45 on a pigtail |
All other models |
1 female RJ-45 |
|
Video input and loop through — transmitters |
Number/signal type |
|
MTP T 15HD A |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM |
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
Connectors |
|
MTP T 15HD A |
2 female 15-pin HD |
All other transmitters |
1 female 15-pin HD |
Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
Impedance |
75 ohms |
Horizontal frequency |
15 kHz to 130 kHz |
Vertical frequency |
30 Hz to 150 Hz |
Return loss |
<-30 dB @ 5 MHz |
DC offset (max. allowable) |
250 mV |
|
Video output — receivers (MTP RL 15HD A, MTP RL 15HD A SEQ, MTP R 15HD RSA D) |
Number/signal type |
|
MTP R 15HD RSA D |
1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video |
All other receivers |
1 set of proprietary analog signals
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
Connectors |
|
MTP R 15HD RSA D |
1 female 15-pin HD |
All other receivers |
1 female RJ-45
1 female 15-pin HD |
Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
Minimum/maximum levels |
0.3 V to 1.45 Vp-p |
Impedance |
75 ohms |
Return loss |
<-30 dB @ 5 MHz |
DC offset |
|
MTP R 15HD RSA D |
<±20 mV with input at 0 offset |
All other receivers |
<±35 mV with input at 0 offset |
Skew compensation |
62 ns |
Maximum resolution |
Up to 1920x1200 or 2048x1080 or 1080p at 300'
Up to 1024x768 at 600' |
NOTE |
See the user guide for the maximum distances recommended for specific resolutions. |
|
|
Sync |
Input type (transmitters) |
RGBHV, RGBS, RGsB, RsGsBs |
Output type (receivers) |
RGBHV, RGBS, RGsB, RsGsBs |
Standards |
NTSC 3.58, NTSC 4.43, PAL, SECAM |
Input level (transmitter) |
3.5 V to 5.5 Vp-p, unterminated |
Output level (receivers) |
4.0 V to 5.0 Vp-p, unterminated |
Input impedance (transmitter) |
573 ohms ±5% |
Output impedance (receivers) |
110 ohms |
Max. input voltage (transmitter) |
5.5 V p-p |
Polarity |
|
Transmitter |
Positive or negative (follows input polarity) |
Receivers |
Positive or negative (switch-selectable) |
|
Audio — all models |
Number/signal type |
1 set of proprietary analog signals |
Connectors |
1 female RJ-45 |
Gain |
Unbalanced output: 0 dB; balanced output: +6 dB |
Frequency response |
20 Hz to 20 kHz, ±1 dB |
THD + Noise |
0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
S/N |
>70 dB at maximum output (unweighted) |
Stereo channel separation |
>60 dB @ 1 kHz |
CMRR |
>43 dB @ 20 Hz to 20 kHz |
|
Audio input — transmitters |
Number/signal type |
1 stereo, unbalanced |
Connectors |
(1) 3.5 mm mini stereo jack |
Impedance |
>10k ohms, unbalanced |
Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
Maximum level |
+18 dBu, (unbalanced) at 1%THD+N |
NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
Audio output — MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM local stereo output |
Number/signal type |
1 stereo, balanced/unbalanced |
Connectors |
(1) 3.5 mm direct insertion captive screw connector, 5 pole |
Impedance |
50 ohms unbalanced, 100 ohms balanced |
Gain error |
±1 dB channel to channel |
Maximum level (Hi-Z) |
>+23 dBu, balanced or unbalanced at 1% THD+N |
Maximum level (600 ohm) |
>+17 dBm, balanced or unbalanced at 1% THD+N |
|
Audio output — receivers |
Number/signal type |
|
MTP R 15HD RSA D |
1 mono, balanced/unbalanced |
All other receivers |
2 mono, balanced/unbalanced |
Connectors |
|
MTP R 15HD RSA D |
(1) 3.5 mm captive screw connector, 5 pole (uses 3 poles) |
All other receivers |
(1) 3.5 mm captive screw connector, 5 pole |
Impedance |
50 ohms unbalanced, 100 ohms balanced |
Gain error |
±1 dB channel to channel |
Nominal level |
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
Maximum level |
|
MTP R 15HD RSA D |
14 dBm, unbalanced at 1% THD+N |
All other receivers |
+18 dBu, unbalanced at 1% THD+N |
|
Control/remote — external device (pass-through, unidirectional or bidirectional) — MTP R 15HD RSA D only |
Serial control port input/output |
1 set of proprietary signals on a female RJ-45 jack |
Serial control port output/input |
RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole |
Baud rates |
Up to 38400 bps at up to 1000' (304.8 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) |
Protocol |
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
NOTE |
Protocol is mirrored between the transmitter and the receiver. |
|
Serial control pin configuration |
Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND |
|
General |
Recommended cable type |
CAT 5/5e/6 (shielded or unshielded) |
Power supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
Power input requirements |
12 VDC, 0.5 A |
Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
Cooling |
Convection, no vents |
Mounting |
|
Rack mount |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional rack shelf |
Furniture or wall mount |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional under-desk mounting kit |
MTP T 15HD A AAP |
Yes, with optional AAP mounting faceplates that have double space high AAP opening |
MTP T 15HD A D, MTP R 15HD RSA D |
Yes, in a Decora®-style opening with a standard electrical wall box or Decora size mud ring |
MTP T 15HD A WM |
Yes, in a 1-gang opening |
Pole mount |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
Yes, with optional pole mounting kit |
Enclosure type |
Metal |
Enclosure dimensions |
|
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ |
1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.) |
Faceplates |
|
MTP T 15HD A AAP |
1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D)
(double space high AAP plate) |
MTP T 15HD A D, MTP R 15HD RSA D |
2.6" H* x 1.3" W x 0.1" D (6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang, 4.4" H x 2.7" W Decora-style wallplate. Depth excludes connectors.)
*Overall height is 4.1" (10.4 cm) including mounting tabs. |
MTP T 15HD A WM |
4.5" H x 2.8" W x 0.1" D (11.4 cm H x 7.1 cm W x 0.3 cm D) (1 gang) |
Device |
|
MTP R 15HD RSA D |
2.75" H x 1.65" W x 1.3" D
(7.0 cm H x 4.2 cm W x 3.3 cm D)
(Depth excludes connectors.) |
Other AAP, D, and WM models |
2.7" H x 1.4" W x 1.4" D (6.9 cm H x 3.6 cm W x 3.6 cm D)
(Depth excludes connectors.) |
Product weight |
0.4 lbs (0.2 kg) |
Shipping weight |
2 lbs (1 kg) |
Vibration |
ISTA 1A in carton (International Safe Transit Association) |
Regulatory compliance |
|
Safety |
CE, c-UL, UL |
EMI/EMC |
CE, C-tick, FCC Class A, ICES, VCCI |
Warranty |
3 years parts and labor |